CNSK Edge banding machinery · Dongguan Request a configuration
Dongguan, China · Since 2006

The edge is where a cabinet is judged.

CNSK builds edge banding machines for factories that have to get the corner right — laser and PUR, 45° bevels, thirty handle-free profiles and arcs, on panels from 8 mm to 60 mm.

Request a configuration See the machines
CN500 servo heavy-duty laser edge bander on the CNSK test floor in Dongguan
CN500 · Laser bonding, no glue line 8–45 mm
2006
Building edge banders in Dongguan
40,000 m²
Plant area at the current Dongguan site
3,000+
Machines built per year
40+
Technology patents held

Five formats.
One factory.

Each machine is built to the panel and the profile a buyer actually runs — station list, tooling and voltage fixed at order stage.

CN500 — Servo Heavy-Duty Laser Edge Bander
CN500

Servo Heavy-Duty Laser Edge Bander

Laser bonding with no glue line, on panels from 8 mm and strips down to 40 mm.

Laser bonding8–45 mm40 mm stripsCut-outs
Read the specification
FM758JC Ultra — Double-Layer Handle-Free Edge Bander
FM758JC Ultra

Double-Layer Handle-Free Edge Bander

Thirty handle-free profiles on one machine, switched from the screen with no waiting between shapes.

30 profilesPUR readyOne-click changeQR feeding
Read the specification
FM750JC — 45° Bevel & Straight Edge Bander
FM750JC

45° Bevel & Straight Edge Bander

The 45° bevel and the straight edge finished on the same line, plus soft-forming for wrapped profiles.

45° bevelStraightSoft-formingExport standard
Read the specification
FM725YCX — Five-Profile Arc & Bevel Edge Bander
FM725YCX

Five-Profile Arc & Bevel Edge Bander

Half-round, quarter-round, 45° bevel-straight, full bevel and duck-bill — five profiles on one bed.

5 profilesArc R15 / R13 / R2045° bevelDuck-bill
Read the specification
FM490G — Servo Narrow-Panel Edge Bander
FM490G

Servo Narrow-Panel Edge Bander

Forty-millimetre strips, 9–60 mm thick, at 16–23 m/min — with servo control on the stations that decide the finish.

≥40 mm width9–60 mm thick16–23 m/min25 kW
Read the specification

What happens between the panel and the polish.

The stations are the specification. A machine is worth what its weakest station holds — which is why the trimming and corner heads are servo, not spring.

01
Pre-milling
Two cutters re-finish the saw marks, burrs and any out-of-square edge before the band goes on.
02
Heating
Panel and glue are pre-heated so the melt reaches the surface it has to hold.
03
Gluing
EVA pot with fast-melt tank, or PUR, applied to the face being banded.
04
Pressing
Servo-controlled pressure and downstroke, adjusted to the band thickness.
05
End trimming
Front and rear of the band cut square, with automatic oiling on the mechanism.
06
Rough trimming
A uniform margin is left for the fine heads; servo feed keeps it even across the panel.
07
Fine trimming
Cut to 0.01 mm from the screen, with the R value saved against the band thickness.
08
Corner rounding
Four independent servo heads track each corner for a clean R.
09
Edge scraping
The R is scraped flat and bright, again from a stored recipe.
10
Polishing
Cotton wheels clean the finished edge; the separating agent keeps residual glue off the face.

Not every model carries all ten stations. The FM490G runs the full sequence; laser and arc platforms replace the glue station with their own bonding or profile tooling.

CNSK factory site in Dongguan, Guangdong
The current plant, Dongguan: 40,000 m² and capacity for 3,000 machines a year.

Built where the machines are tested.

The factory started in 2006 as Dongguan FanMao, building panel-furniture equipment for the Chinese home market. The edge bander became the product that mattered, and CNSK became the name it shipped under.

The plant in Dongguan assembles, wires and test-runs every machine before it leaves, so the panel that decides the acceptance is cut on the same floor the machine was built on.

Factory, patents and certifications
CE certificate of conformity for CNSK edge banding machines
CE under 2006/42/EC, certificate M.2024.206.C111789, valid to 22 December 2029.

The paperwork a European buyer asks for first.

Machinery Directive attestation issued by UDEM International Certification, Ankara, held alongside ISO 9001:2015 and the national high-tech enterprise designation.

  • CE — Machinery DirectiveCertificate M.2024.206.C111789, issued by UDEM under 2006/42/EC Annex VIII. Valid to 22 December 2029.
  • ISO 9001:2015Quality management system certification held by the manufacturing entity.
  • National High-tech EnterpriseRecognised under the national high-tech enterprise programme, with core independent IP and technology transfer.

Where the machines are working.

Export started in Southeast Asia and moved out from there. Most orders now ship to buyers who run their own showroom or service team locally.

EuropePoland · Romania · Italy · UK
Middle EastSaudi Arabia · Israel · UAE
Southeast AsiaIndonesia · Vietnam · Malaysia
South AmericaBrazil · Argentina
AfricaNorth and West Africa
OceaniaAustralia
Edge banding machines loaded for export at the CNSK plant
Container loading in Dongguan. Machines are crated with the station list and tooling matched to the order.

Send the panel spec. Get a configuration, not a catalogue.

Thickness, width, band material and the profile you sell. That is enough to put a station list and a price against your name.

Start an inquiry or message WhatsApp +86 138 2571 8325